Mechanical | Format | Standard profile, half length, 4-lane PCI Express card | Cooling method | Air cooling, fan-cooled heatsink | Mounting | For insertion in a standard height, 4-lane or higher, PCI Express card slot | Connectors | - 'A', 'B', 'C', 'D' on bracket:
- 4x DIN 1.0/2.3 female connectors
- CoaXPress host interface
- 'DA', 'DB', 'DC', 'DD' on bracket:
- 4x DIN 1.0/2.3 female connectors
- CoaXpress data forwarding interface
- 'INTERNAL I/O 2' on PCB:
- 26-pin 2-row 0.1" pitch pin header with shrouding
- I/O lines and power output
- 'AUXILIARY POWER INPUT' on module:
- 6-pin PEG power socket
- 12 VDC power input for PoCXP camera(s) and I/O
- 'C2C-LINK' on module:
- 6-pin 2-row 0.1-in header
- Card to card link
| LED indicators | - 'A', 'B', 'C', 'D' on bracket:
- Bi-color red/green LEDs
- CoaXPress Host connector indicator
- 'FPGA STATUS LAMP' on PCB:
- Bi-color red/green LED
- FPGA status indicator
- 'BOARD STATUS LAMP' on PCB:
- Bi-color red/green LED
- Board status indicator
| Switches | 'RECOVERY' on card PCB:- 3-pin 1-row 0.1" header
- Firmware emergency recovery
| Dimensions | L 167.65 mm x H 111.15 mm L 6.6 in x H 4.38 in | Host bus | Standard | PCI Express 3.0 | Link width | - 4 lanes
- 1 lane or 2 lanes with reduced performance
| Link speed | - 8.0 GT/s (PCIe 3.0)
- 5.0 GT/s (PCIe 2.0) with reduced performance
| Maximum payload size | 512 bytes | DMA | 32- and 64-bit | Peak delivery bandwidth | 3,900 MB/s | Effective (sustained) delivery bandwidth | 3,350 MB/s (Host PC motherboard dependent) | Power consumption | Typ. 16.8 W (3.8 W @ +3.3V, 13 W @ +12V), excluding camera and I/O power output | Camera / video inputs | Interface standard(s) | CoaXPress 1.0, 1.1 and 1.1.1 | Connectors | Four DIN1.0/2.3 75 Ohms CXP-6 | Status LEDs | One CoaXPress Host connection status LED per connection | Number of cameras | - Area-scan cameras:
- One 1- or 2- or 4-connection camera
- Line-scan cameras:
- One 1- or 2- or 4-connection camera
| Maximum aggregated camera data transfer rate | 25 Gbit/s (2,500 MB/s) | Supported CXP down-connection speeds | 1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), and 6.25 GT/s (CXP-6) | Number of CXP data streams (per camera) | 1 data stream per camera | Maximum CXP stream packet size | 16,384 bytes | PoCXP (Power over CoaXPress) | - PoCXP Safe Power:
- 17 W of 24V DC regulated power per CoaXPress connector
- PoCXP Device detection and automatic power-on
- Overload and short-circuit protections
- On-board 12V to 24V DC/DC converter
- A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
| Camera types | - Area-scan cameras:
- Grayscale and color (YCbCr, YUV, RGB and Bayer CFA)
- Single-tap (1X-1Y) progressive-scan
- Line-scan cameras and contact imaging sensors:
| Camera pixel formats supported | Raw, Monochrome, Bayer, RGB, and RGBA (PFNC names):- Raw
- Mono8, Mono10, Mono12, Mono14, Mono16
- BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
- RGB8, RGB10, RGB12, RGB14, RGB16
- RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
- YCbCr601_422_8, YCbCr601_422_10
- YCbCr709_422_8, YCbCr709_422_10
- YUV422_8, YUV422_10
| Area-scan camera control | Trigger | - Precise control of asynchronous reset cameras, with exposure control.
- Support of camera exposure/readout overlap.
- Support of external hardware trigger, with optional delay and trigger decimation.
| Strobe | - Accurate control of the strobe position for strobed light sources.
- Support of early and late strobe pulses.
| Line-scan camera control | Scan/page trigger | - Precise control of start-of-scan and end-of-scan triggers.
- Support of external hardware trigger, with optional delay.
- Support of infinite acquisition, without missing line, for web inspection applications.
| Line trigger | - Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
- Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
- Rate Divider tool
| Line strobe | - Accurate control of the strobe position for strobed light sources.
| On-board processing | On-board memory | 1 GB |
Mechanical | Format | Standard profile, half length, 4-lane PCI Express card | Cooling method | Air cooling, fan-cooled heatsink | Mounting | For insertion in a standard height, 4-lane or higher, PCI Express card slot | Connectors | - 'A', 'B', 'C', 'D' on bracket:
- 4x DIN 1.0/2.3 female connectors
- CoaXPress host interface
- 'EXTERNAL I/O' on bracket:
- 26-pin 3-row high-density female sub-D connector
- I/O lines and power output
- 'INTERNAL I/O 1' and 'INTERNAL I/O 2' on PCB:
- 2x 26-pin 2-row 0.1" pitch pin header with shrouding
- I/O lines and power output
- 'AUXILIARY POWER INPUT' on module:
- 6-pin PEG power socket
- 12 VDC power input for PoCXP camera(s) and I/O power
- 'C2C-LINK' on module:
- 6-pin 2-row 0.1-in header
- Card to card link
| LED indicators | - 'A', 'B', 'C', 'D' on bracket:
- Bi-color red/green LEDs
- CoaXPress Host connector indicator
- 'FPGA STATUS LAMP' on PCB:
- Bi-color red/green LED
- FPGA status indicator
- 'BOARD STATUS LAMP' on PCB:
- Bi-color red/green LED
- Board status indicator
| Switches | 'RECOVERY' on card PCB:- 3-pin 1-row 0.1" header
- Firmware emergency recovery
| Dimensions | L 167.65 mm x H 111.15 mm L 6.6 in x H 4.38 in | Weight | 170 g, 6.00 oz | Host bus | Standard | PCI Express 2.0 | Link width | - 4 lanes
- 1 lane or 2 lanes with reduced performance
| Link speed | - 5.0 GT/s (PCIe 2.0)
- 2.5 GT/s (PCIe 1.0) with reduced performance
| Maximum payload size | 512 bytes | DMA | 32- and 64-bit | Peak delivery bandwidth | 2,000 MB/s | Effective (sustained) delivery bandwidth | 1,700 MB/s (Host PC motherboard dependent) | Power consumption | Typ. 12.1W ( 2.5 W @ +3.3V, 9.6 W @ +12V), excluding camera and I/O power output | Camera / video inputs | Interface standard(s) | CoaXPress 1.0, 1.1 and 1.1.1 | Connectors | Four DIN1.0/2.3 75 Ohms CXP-3 | Status LEDs | One CoaXPress Host connection status LED per connection | Number of cameras | Up to four 1-connection cameras | Maximum aggregated camera data transfer rate | 12.5 Gbit/s (1,250 MB/s) | Supported CXP down-connection speeds | 1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3) | Number of CXP data streams (per camera) | 1 data stream per camera | Maximum CXP stream packet size | 8,192 bytes | PoCXP (Power over CoaXPress) | - PoCXP Safe Power:
- 17 W of 24V DC regulated power per CoaXPress connector
- PoCXP Device detection and automatic power-on
- Overload and short-circuit protections
- On-board 12V to 24V DC/DC converter
- A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
| Camera types | - Grayscale
- Color (RGB and Bayer CFA)
| Camera pixel formats supported | Raw, Monochrome, Bayer, RGB, and RGBA (PFNC names):- Raw
- Mono8, Mono10, Mono12, Mono14, Mono16
- BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
- RGB8, RGB10, RGB12, RGB14, RGB16
- RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
- YCbCr601_422_8, YCbCr601_422_10
- YCbCr709_422_8, YCbCr709_422_10
- YUV422_8, YUV422_10
| Area-scan camera control | Trigger | - Precise control of asynchronous reset cameras, with exposure control.
- Support of camera exposure/readout overlap.
- Support of external hardware trigger, with optional delay and trigger decimation.
| Strobe | - Accurate control of the strobe position for strobed light sources.
- Support of early and late strobe pulses.
| On-board processing | On-board memory | 1 GB |
|
|
所有评论仅代表网友意见,与本站立场无关。